Royer Labs R-122 MKII Active Live Ribbon Microphone™ Figure-8 (eight)

AMPT-Rover R122 MK2
R-122 MKII Active
excl Verzendkosten kg
    Levertijd:1-3 dagen
  • Beschrijving
  • Meer

Royer Labs  R-122 MKII Active Live Ribbon Microphone™  Figure-8 (eight)

The R-122 MKII Live is a road-optimized version of our phantom powered R-122 ribbon microphone.

 The R-122 MK2 Live's output is on par with phantom powered condenser ribbon mics and it produces the warm, realistic sounds that only ribbon mics can deliver.

Along with its smooth, natural response, the R-122 Live virtually eliminates the shrill high-end often encountered with live guitars, brass and drum cymbals. Push up the faders and there's the instrument in all its fullness, minus the peaky highs that FOH and Monitor engineers spend so much of their careers fighting.
The R-122 MKii Live contains a fully balanced, discrete head amplifier system utilizing a specially wound toroidal transformer and ultra-low noise FET's. This system is extremely quiet, can handle 135 dB SPL, and brings the R-122's sensitivity to -37 dB.

The R-122 can be used on extremely long cable runs with minimal RF interference and signal loss, and the ribbon element cannot be damaged by phantom power, miswired cables or electrical glitches.

The R-122 Live is visually differentiated by its red logo. The ribbon element thickness is increased from 2.5-microns to 4-microns, giving the microphone greater durability and a slightly reduced high end response.

Highs are often rolled off in live performances, but due to the R-122 Live's exceptionally smooth high frequency response, it needs far less eq'ing than is usually required with condenser and dynamic microphones.

The R-122 Live is backed with Royer's lifetime warranty to the original owner, and the first re-ribbon is free. We expect it to work as hard as you do, so we stand behind it the whole way.

As with any high end microphone, proper storage during transit and careful handling during setup and breakdown is key to keeping the microphone in good working order.

Figure-8's On Stage: The R-122 Live's pickup pattern is figure-8, which can be used to control stage bleed with great effect. Side rejection in the null points is strong - position the mics "ears" to face the offending instrument(s) and bleed will be virtually eliminated. The top and bottom of the microphone are also null points. If monitors are in close proximity to the rear side of the microphone, a positioning adjustment can place the monitors output in the mic's null, isolating the monitor from the mic's pickup areas.

Patented Offset Ribbon Technology: The R-122 Live's proprietary offset ribbon transducer (Patent # 6,434,252) is the first of its kind, positioning the ribbon element closer to the front (logo) side of the microphone. This arrangement gives the ribbon more room to move within the prime magnetic field while maintaining full frequency response on high SPL applications. It's an integral piece of the magic of all Royer R-series microphones.

Features: Phantom powered circuitry provides high output and impedance matching.  High SPL Capabilities. No distortion up to maximum SPL rating. Extremely low residual noise. Ribbon element is not affected by heat or humidity. Absence of high frequency phase distortion. Equal sensitivity from front or back of element. Consistent frequency response regardless of distance. Rear side of mic records slightly brighter when three feet or closer to sound source

Specs: Acoustic Operating Principle: Electrodynamic pressure gradient with active electronics. Polar Pattern: Figure-8. Generating Element: 4-micron aluminum ribbon. Magnets: Rare Earth Neodymium. Frequency Response: 30 -15,000 Hz +/- 3dB. Sensitivity: -37 dB (referenced 1v/pa +/- 2dB). Self-Noise: < 20 dB. Output Impedance: 200 Ohms, balanced. Rated Load Impedance: 1K-Ohm. Maximum SPL: >135dB.  Output Connector: Male XLR 3 pin (Pin 2 Hot). Dimensions: 206mm L X 25mm W (8 1/8" L X 1" W).Weight: 309 grams (10.9 oz).  Finish: Dull Satin Nickel/Matte Black Chrome optional.